Waterworks SD19 Bench Top Mains Pressure Drain Free Water Cooler

The SD5 series is a smaller "bench top" cooler with all the advantages of its' taller relative (D5). The large 12L reservoir offers a never ending supply of refreshing cool/cold or hot/cold water. These mains connected, drain free centres connect to a variety of water filtration products and are covered by a 2 year warranty.

GENERAL FEATURES

D5 series point of use (P.O.U.) Water centres provide a
never ending supply of refreshing Hot & Cold or Cool & Cold
water.
They attach directly to your water source and are able
to accommodate a variety of purifiers.
The large 12 litre reservoir makes it the ideal choice for use with Reverse
Osmosis purification systems and the fast flow levers and high
clearance recessed alcove make it easy to draw water.

SPECIFICATIONS:

CABINET:
Top and front panels are moulded of UV treated ABS and side
panels are zinc coated steel sheets covered in electrostatically
applied high polymer polyester resin.
COLOUR:
High gloss cloud white available as standard.
DRIP TRAY:
Concealed lift-out design of a high impact durable plastic.
Removable for sanitation, it incorporates an anti-splash grid
which diverts drain water into the drip tray.
TAPS:
High impact polypropylene lever type. Fast flow and easy to
operate. They’re assembled directly onto the reservoir and are
fully recessed for added protection. Taps are 177mm above the
drain grid allowing ample room for filling kettles and other tall
objects. Hot tap has safety influence.
TOP:
One piece heat resistant plastic. This rust-proof top provides a
flat surface to hold small coffee servers and trays.
FUNCTION STATUS DISPLAY:
Waterworks unique design. This exclusive device illuminates a
red green signal indicating the Power/Hot/Cold position of the
dispenser.
COOLING RESERVIOR:
Constructed of polypropylene plastic, approximately 12 litres
in capacity. The reservoir features large radius corners to
facilitate cleaning. The integrated zoned waterway and baffle
system prevents ice rings from restricting chilled water flow.
Cold water capacity below the baffle is 4.2 litres. Water above
the baffle stays at or about room temperature.
HOT TANK:
Type 304 stainless steel. 500 Watt sheathed heater installed in
the tank ensures accurate temperature control. On/Off switch
is easily accessible at side of cabinet. Tank capacity is 2 litres.
AIR FILTER:
Located on the float assembly for easy access. The air
filter contains a replaceable filter disc with a one micron
membrane media.
FLOAT ASSEMBLY:
One stage polyethylene float valve system incorporates a
primary float valve which maintains the water level in the
reservoir and shuts off when full. The system is designed to
operate on an incoming water pressure range of 140-700kPa and
a pressure limiting valve should be fitted in situations where the
mains pressure may fluctuate to greater than 700kpa.
REFRIGERATION SYSTEM:
Ozone friendly HFC-134a refrigerant. Flow is controlled by
capillary tube which has no moving parts. Condenser is air
cooled static type for silent running. No fan assembly is
required. Compressor is hermetically sealed, permanently
lubricated and protected against motor overload.
THERMOSTAT:
Adjustable and user friendly. Readily accessible at the side of
the cabinet.
ELECTRICAL:
240 Volts 50Hz single phase. A 1.8 metre house cable and 3 pin
plug is supplied. Full load current is 1.5 amps.
PERFORMANCE:
Tap 1 Outlet water 9DC approx
Tap 2 Outlet water 18DC approx
Hot Tap Outlet water 88DC approx
CAPACITIES CHART
Room Temp 150ml Cups/Hr at 10°C Litres/Hr at 10°C
21°C 44 6.6
27°C 32 4.8
32°C 18 2.7
HOT WATER DELIVERY:
45 x 170ml cups p/hr
SHIPPING WEIGHT:
D5C: 20kg SD5C: 15kgs
D5CH: 22kg SD5CH: 17kg
DIMENSIONS:
D5C/D5CH: 310mmW x 310mmD x 1040mmH
SD5C/SD5CH: 310mmW x 310mmD x 630mmH
WARRANTY:
The entire range of Waterworks D5 Series wate

Filtered options available – Please discuss with our Consultants